Products & Services

Anodizing Products
Antiquing Solutions
Black Oxide and Phosphate
Chromates / Conversion Coatings
Cleaner / Coater for Painting
Cleaning / Pre-treatment Processes
Electroplating Processes
Electropolishing and Bright Dips
Galvanizing & Miscellaneous Products
Sealers and Top Coats
Stripping Products
Waste Treatment Products

Anodizing Products

Product NameSummaryCategoryTech Data SheetSafety Data Sheet
ALUMINUM DYE CHARTThis is a dye chart of available colours for Aluminum. TDS
DYNAL DYE BUFFER SOLUTIONUsed to help stabilize and buffer seal baths against hard to control pH fluctuations. TDS SDS
DYNAL EC 60Electrolytic colouring process that can produce a wide range of light fast colours on anodized aluminum. TDS SDS
DYNAL EELiquid additive for use in sulphuric anodizing baths, which allows for higher current densities without burning in both conventional and hard anodizing. Contains an algaecide. TDS SDS
DYNAL FSConcentrated liquid additive used to create a controlled foam blanket to minimize the release of sulphuric acid fumes into the air while anodizing. TDS SDS
DYNAL GOLD 4NInorganic colorant used to achieve various shades of gold and brass for coloring anodic coatings on aluminum TDS SDS
DYNAL LFALiquid fluoride concentrate designed to adjust the pH of low temperature seal products. TDS SDS
DYNAL PCALiquid additive used to raise and help buffer the pH of the seal. Can be used in all seal baths to help promote seal, minimize smut and extend bath life. TDS
DYNAL PCA-2Liquid additive used to raise and help buffer the pH of the seal. Can be used in all room temperature seal baths to help promote seal, minimize smut and extend bath life. TDS
DYNAL SCALiquid seal additive designed to eliminate smut seal and water spots.
DYNAL SEALANT LTLow temperature sealant (120-160F). Concentrated Liquid product designed to give a high quality seal and does not affect dyes. Non-yellowing, smut free sealing. Meets all current seal tests. TDS
DYNAL SEALANT MTMid temperature sealant (160-190F). Concentrated Liquid product designed to give a high quality seal and does not affect dyes. Low-foaming, non-yellowing, smut free sealing. Meets all current seal tests. TDS SDS
DYNAL SEALANT MT #2Mid-temperature sealing system for anodized aluminum. TDS SDS
DYNAL SEALANT NFNon-nickel sealant (180-210F). Concentrated liquid product designed to give a high quality seal and does minimal leaching of dyes. Non-yellowing, smut free sealing. Meets all current seal tests. TDS
DYNAL SEALANT RTRoom temperature sealant (70-90F). Concentrated Liquid product designed for good paint and weather stripping adhesion. pH regulated, non-yellowing, smut free sealing. Meets all anodizing specifications. TDS SDS
DYNAL SEALANT RT #2Low temperature sealing system for anodized aluminum. TDS SDS
DYNATREAT DEFOAMER #4Special additive to control foam on an anodizing line. TDS
DYNATREAT DEFOAMER #5Special spray additive to control foam on an anodizing line. TDS

Antiquing Solutions

Product NameSummaryCategoryTech Data SheetSafety Data Sheet
DYNAFIN 4740Liquid concentrate that is diluted with water to produce decorative oxide finishes on a variety of base metals. Range of colour tones are from brown to purple to greyish black. TDS SDS
DYNAFIN 511Liquid concentrate that is diluted with water to produce decorative oxide finishes on copper, copper alloys and nickel. Produces a range of colours from jet black to light brown on copper and copper alloys and light grey to black on nickel. TDS SDS
DYNAFIN 512Liquid concentrate that is diluted with water to produce decorative oxide finishes on copper alloys. DYNAFIN 512 produces more pronounced brown to chocolate brown colors than DYNAFIN 511. TDS SDS
DYNAFIN 513Liquid concentrate that is diluted with water to produce decorative oxide finishes on copper alloys. DYNAFIN 513 is similar to DYNAFIN 512, but produces richer brown tones. TDS SDS
DYNAFIN 514Liquid concentrate that is diluted with water to produce decorative oxide finishes on copper and copper alloys. DYNAFIN 514 produces a range of colours from medium-dark brown to black. TDS SDS
DYNAFIN 526Liquid concentrate that is diluted with water to produce decorative oxide finishes on pewter, tin alloys and lead alloys. The depth of black can be controlled by varying the concentration and immersion time TDS SDS
DYNAFIN 529Liquid concentrate that is diluted with water to produce decorative oxide finishes on copper and copper alloys. DYNAFIN 529 produces a range of colours from light brown, grey, purple and black/pewter on copper and copper alloys. TDS SDS
DYNAFIN 530Liquid concentrate that is used full strength or diluted with water to produce decorative oxide finishes on pewter and tin. TDS SDS
DYNAFIN 550Liquid concentrate that is diluted with water to produce decorative oxide finishes on copper and copper alloys. DYNAFIN 550 produces a range of colours from light brown to blackish brown on copper and copper alloys. TDS SDS
DYNAFIN AGLiquid concentrate that is used to produce natural verdi or patina green colour on copper alloys. TDS
DYNAFIN RTCLiquid product used at full strength or diluted with water to produce natural Verdi, patina green or bluish colours on copper alloys. TDS SDS

Black Oxide and Phosphate

Product NameSummaryCategoryTech Data SheetSafety Data Sheet
DYNAFIN 507Blackening process that produces a black oxide finish on a variety of stainless steels, cast iron as well as mild steel and low carbon steels. The coatings produced complies to mil-DTL-13924D, Class 4. TDS SDS
DYNAFIN 520Produces a jet-black adherent black oxide finish on copper and copper alloys. The coatings produced are chemically and heat stable to a temperature of 400F. Applying oil, wax or a lacquer will help enhance the corrosion protection. TDS SDS
DYNAFIN 520 LLiquid version of Dynafin 520. TDS SDS
DYNAFIN BZProduces a jet- black, adherent, chemically and heat stable black oxide finish on zinc and zinc alloys. The coatings should be protected with wax, oil, or lacquer. TDS SDS
DYNAFIN BZ-2Produces a jet- black, adherent, chemically and heat stable black oxide finish on zinc and zinc alloys. The coatings should be protected with wax, oil, or lacquer. TDS SDS
DYNAFIN CSLiquid, chromium containing zinc phosphate sealer to increase the corrosion resistance of subsequent oil or paint finishes. TDS SDS
DYNAFIN HBOHot black oxide solution for steel and cast iron. Meets MIL C - 13924B for class 1 coatings. TDS SDS
DYNAFIN HBO LLiquid hot black oxide solution for steel and cast iron. Meets MIL C - 13924B for class 1 coatings. TDS SDS
DYNAFIN ICSChromium containing iron phosphate sealer to increase the corrosion resistance of subsequent oil or paint finishes. TDS
DYNAFIN NCLiquid inhibitive rinse applied on most phosphate surfaces to promote paint adhesion and reduce drip and run-down staining while increasing corrosion protection. Suitable for use on iron, zinc, calcium and manganese modified phosphate surfaces. TDS SDS
DYNAFIN NCSLiquid, non-chrome containing inhibitive rinse applied on iron phosphate surfaces and is designed to increase corrosion protection and promote paint adhesion. TDS
DYNAFIN RTBRoom temperature, immersion process designed to blacken carbon steel surfaces. TDS SDS
DYNAFIN RTBARoom temperature, immersion process designed to blacken aluminum surfaces. TDS SDS
DYNAFIN RTBSRoom temperature, immersion process designed to blacken stainless steel surfaces. TDS SDS
DYNAPHOS CPLiquid, immersion, calcium-modified zinc phosphate used to produce exceptionally fine-grained, smooth, conversion coatings on steel. The microcrystalline coating provides excellent corrosion resistance and paint adhesion. TDS SDS
DYNAPHOS FeRNeutral, liquid product used as an accelerator in zinc phosphate solutions. Dynaphos FeR may be used in spray and immersion applications. TDS SDS
DYNAPHOS FGLow temperature, nickel-free, zinc phosphate used to produce fine grain crystalline conversion coating on steel surfaces in spray and immersion applications. Meets the requirements of TT-C-490B Type I, QQ-Z-352C Type III and QQ-P-416C Type III. TDS SDS
DYNAPHOS HZLiquid, immersion zinc phosphate used to produce fine grain crystalline heavyweight coatings on steel surfaces. Meets the requirements of ASTM F1137, MIL-DTL-16232G TYPE Z and A-A59267 when properly applied. TDS SDS
DYNAPHOS HZ-CSLiquid, immersion zinc phosphate used to produce fine grain crystalline heavyweight coatings on steel surfaces while generating minimal sludge. Meets the requirements of ASTM F1137, MIL-DTL-16232G TYPE Z and A-A59267 when properly applied. TDS SDS
DYNAPHOS MPLiquid, immersion manganese phosphate used to produce a fine grain crystalline heavyweight coatings on steel surfaces. Meets the requirements of MIL-DTL-16232G, TYPE M and MIL-P-50002 when properly applied. TDS SDS
DYNAPHOS OIL # 1Water-soluble rust preventative for steel and zinc phosphated steel. Dry to touch formulation that will add good salt spray protection when applied to Dynaphos HZ. TDS SDS
DYNAPHOS OIL # 2Water-soluble rust preventative for steel and zinc phosphated steel. Dry to touch formulation that will add 200 hours of salt spray protection when applied to Dynaphos HZ. TDS SDS
DYNAPHOS PBLiquid concentrated additive used for producing black phosphate coatings. TDS SDS

Chromates / Conversion Coatings

Product NameSummaryCategoryTech Data SheetSafety Data Sheet
DYNAFIN CBAlkaline, chrome-based passivating solution for copper and brass. DYNAFIN CB will help prevent spotting and bleed out, common with cyanide plating solutions, and will increase corrosion resistance while preserving the colour of the deposit. TDS SDS
DYNAFIN CBSAlkaline, chrome-based, cathodic passivating solution for copper, brass, bronze and silver. Helps prevent spotting and bleed out, common with cyanide plating solutions. TDS SDS
DYNAFIN HCCAdditive used to reduce chromate leaching, rub off and staining. Will increase corrosion resistance on hexavalent chromates and can be used with yellow, olive drab and black chromates. TDS SDS
DYNAPASS CADPowdered, hexavalent, clear, bright, polished conversion coating for cadmium plated parts. It offers a wide operating window, ease of operation and excellent corrosion protection along with a crisp, bright and polished finish. TDS SDS
DYNAPASS CAD LLiquid clear hexavalent conversion coating for cadmium plated parts. It offers a wide operating window, ease of operation, good corrosion protection along with a crisp, clear bright and polished finish. TDS SDS
DYNAPASS H Al #2Liquid process which when diluted with water will produce a protective conversion coating for aluminum and aluminum alloys. It offers a wide operating window, ease of operation and meets or exceeds requirements of MIL C 5541. TDS SDS
DYNAPASS H AL LIQUIDProduces a protective conversion coating for aluminum and aluminum alloys. It offers a wide operating window, ease of operation and meets Specifications MIL-C-5541 method A and C to produce Class 3 coatings. TDS SDS
DYNAPASS HALPowdered process which when diluted with water will produce a protective conversion coating for aluminum and aluminum alloys. It offers a wide operating window, ease of operation and meets or exceeds requirements of MIL C 5541. TDS SDS
DYNAPASS HBLiquid hexavalent two part black conversion coating for zinc and zinc alloy plated parts. It offers a wide operating window, ease of operation and excellent corrosion protection along with a polished jet-black non-iridescent finish. TDS SDS
DYNAPASS HCLiquid hexavalent clear conversion coating for zinc plated parts. It offers a wide operating window, ease of operation, good corrosion protection along with a crisp, bright blue polished finish. TDS SDS
DYNAPASS HCPPowdered hexavalent clear conversion coating for zinc plated parts.  It offers a wide operating window, ease of operation, good corrosion protection along with a crisp, bright blue polished finish. TDS SDS
DYNAPASS HGLiquid which, when diluted with water will produce a pleasing forest green conversion coating on zinc and cadmium plated parts along with adequately prepared zinc-die cast parts. Single component. TDS SDS
DYNAPASS HO2 part concentrated liquid which, when diluted with water produce an olive drab conversion coating on zinc and cadmium plated parts along with adequately prepared zinc-die cast parts. TDS SDS
DYNAPASS HYLiquid hexavalent yellow conversion coating for zinc and cadmium plated parts. It offers a wide operating window, ease of operation and excellent corrosion protection along with a crisp, bright and polished yellow iridescent finish. TDS SDS
DYNAPASS HY Zn NiLiquid hexavalent yellow conversion coating for zinc nickel containing 10 and 18 % Nickel. It offers a wide operating window, ease of operation and neutral salt spray protection exceeding 1500 hours to white corrosion. TDS SDS
DYNAPASS HYDLiquid hexavalent yellow conversion coating specifically formulated for use with dyes. TDS SDS
DYNAPASS HYNLiquid hexavalent yellow conversion coating for electroplated zinc parts It offers excellent polishing and corrosion protection, along with a bright yellow iridescent finish TDS SDS
DYNAPASS HYPDynapass HYP is a powdered hexavalent yellow conversion coating for zinc and cadmium plated parts. It offers a wide operating window, ease of operation and excellent corrosion protection along with a polished yellow iridescent finish. TDS SDS
DYNAPASS HZDPowdered hexavalent conversion coating for zinc or cadmium plated parts and zinc diecastings. It provides a high degree of polishing for increased brilliance and the formation of a chromium like surface after leaching. TDS SDS
DYNAPASS NPAdditive for use in Dynapass T120 solution utilizing nano-particle technology representing the latest development in trivalent chromium passivation. TDS SDS
DYNAPASS T 10Liquid trivalent clear conversion coating for zinc-plated parts. It offers a wide operating window, ease of operation and good corrosion protection along with a polished, bright finish. TDS SDS
DYNAPASS T 100Liquid trivalent clear conversion coating for zinc plated parts providing corrosion protection exceeding 72 hours of neutral salt spray testing to white corrosion along with a bright and pleasing blue colour. TDS SDS
DYNAPASS T 103High Corrosion Resistant Trivalent Blue Conversion Coating for Zinc. Wide operating window, ease of operation and corrosion protection exceeding 96 hours of neutral salt spray testing to white corrosion products. TDS SDS
DYNAPASS T 107High Corrosion Resistant Trivalent Blue Conversion Coating for Zinc. Wide operating window, ease of operation and corrosion protection exceeding 96 hours of neutral salt spray testing to white. Baking or drying improves corrosion protection. TDS SDS
DYNAPASS T 110Liquid trivalent clear conversion coating for zinc plated parts providing a wide operating window, ease of operation and good corrosion protection in neutral salt spray testing to white corrosion products. TDS SDS
DYNAPASS T 120Liquid trivalent clear high performance conversion coating for zinc plated parts. It offers a wide operating window, ease of operation and corrosion protection exceeding 175 hours of neutral salt spray testing to white corrosion products. TDS SDS
DYNAPASS T 120-FTIron tolerant version of Dynapass T 120. TDS SDS
DYNAPASS T 130Liquid trivalent blue conversion coating for zinc plated parts. It offers a wide operating window, ease of operation and corrosion protection exceeding 170 hours of neutral salt spray testing to white corrosion products. TDS SDS
DYNAPASS T 175Cobalt Free, Thick Film Trivalent Conversion Coating for Zinc. It offers a wide operating window, ease of operation and corrosion protection exceeding 120 hours of neutral salt spray testing to white corrosion products. TDS SDS
DYNAPASS T 200Liquid trivalent iridescent clear ultra high performance conversion coating for zinc plated parts. It offers corrosion protection exceeding 250 hours of neutral salt spray testing to white corrosion products. TDS SDS
DYNAPASS T 200-FTDynapass T200-FT is a high performance thick-film liquid trivalent iridescent conversion coating for zinc plated parts providing corrosion protection exceeding 250 hours of neutral salt spray testing to white corrosion products. TDS
DYNAPASS T 300High Corrosion Resistant Trivalent Yellow Conversion Coating for Zinc providing up to 120 hours of neutral salt spray testing to white corrosion products. TDS SDS
DYNAPASS T ALLiquid trivalent clear conversion coating for aluminum and aluminum alloys. TDS SDS
DYNAPASS T APPowdered process which when diluted with water will produce a trivalent clear conversion coating for aluminum and aluminum alloys. TDS SDS
DYNAPASS TB 200Liquid, trivalent black passivate for zinc and zinc alloys. It offers uniform black appearance, ease of operation and over 168 hours of neutral salt spray testing to white corrosion products when sealed with DYNACOAT TB 200 SEALER TDS SDS
DYNAPASS TRI DEEP REDDYNAPASS TRI DEEP RED is an additive used with DYNAPASS trivalent chromates to produce a trivalent red conversion coating. TDS SDS
DYNAPASS TRI-GREENDYNAPASS TRI-GREEN is an additive used with DYNAPASS trivalent chromates to produce a trivalent green conversion coating. TDS SDS
DYNAPASS TRI-YELLOW ADDITIVEProduces an attractive trivalent yellow conversion coating which rivals the appearance of a hexavalent yellow conversion coating. TDS SDS
DYNAPASS TRI-YELLOW ADDITIVE PLUSProduces an attractive trivalent yellow conversion coating that rivals the appearance of the hexavalent yellow conversion coating. Can be added directly to most trivalent passivate solution. TDS SDS
SURTEC 650Hexavalent chromium free passivating solutions for aluminum. meets or exceeds MIL-DTL-81706B and MIL-DTL-5541F. TDS SDS
SURTEC 650VHexavalent chromium free passivation for aluminum, meets or exceeds MIL-DTL-81706b and MIL-DTL-5541f for bare corrosion, class 1A, and class 3 TDS SDS

Cleaner / Coater for Painting

Product NameSummaryCategoryTech Data SheetSafety Data Sheet
DYNAPHOS IPLiquid, dual-purpose concentrate used to simultaneously clean and deposit a corrosion inhibitive phosphate coating on steel, galvanized steel and aluminum surfaces. Provides an iridescent, blue coating and is an ideal surface for paint bonding. TDS SDS
DYNAPHOS IP-FFFluoride-free, liquid, concentrate used to simultaneously clean and deposit a corrosion inhibitive phosphate coating on steel, galvanized steel and aluminum surfaces. Provides an iridescent, blue coating and is an ideal surface for paint bonding. TDS SDS
DYNAPHOS IP-HPLiquid, long life, molybdate-free, concentrate used to clean and deposit a corrosion inhibitive phosphate coating on steel, galvanized steel and aluminum surfaces. Formulated to provide a coating weight of 25 mg/ft2 with little or no sludging. TDS SDS
DYNAPHOS IP-LFLiquid, low foaming concentrate used to clean and deposit a corrosion inhibitive phosphate coating on steel, galvanized steel and aluminum surfaces. Provides an iridescent, blue coating and is an ideal surface for paint bonding. TDS SDS
DYNAPHOS SP #1Liquid, iron phosphate specially formulated for steam phosphating of large steel substrates. In one application, this economical process will clean and coat the surface prior to painting at temperatures as low as 38°C (100°F). TDS SDS
DYNAPHOS SP #2Liquid, iron phosphate specially formulated for steam phosphating of large steel substrates. In one application, this economical process will clean and coat the surface prior to painting at temperatures as low as 38°C (100°F). TDS SDS
DYNAPHOS SP #3Liquid, iron phosphate specially formulated for steam phosphating of most metal parts including steel, aluminum and galvanized substrates. This process will clean and coat the surface prior to painting at temperatures as low as 38°C (100°F). TDS SDS
DYNAPREP PFHPhosphate, nonylphenol and nonylphenol ethoxylate-free cleaner and coater for improved paint adhesion for multi-metal applications. Can be used in a single step operation as well as 2 or 3 stage washers. Available in a low-foam version: DYNAPREP PFL TDS SDS
DYNAPREP PFLLow-foaming, phosphate, nonylphenol and nonylphenol ethoxylate-free cleaner and coater for improved paint adhesion for multi-metal applications. Can be used in a single step operation as well as 2 or 3 stage washers. TDS SDS

Cleaning / Pre-treatment Processes

Product NameSummaryCategoryTech Data SheetSafety Data Sheet
ACTIVATOR Cr#1Electrolytic activator for electroplated bright nickel deposits prior to chromium plating. Prevents milky films and stains (white wash) after chrome plating that result from passive bright nickel deposits. TDS SDS
ACTIVATOR Cr#2Electrolytic activator for electroplated bright nickel deposits prior to chromium plating. Prevents milky films and stains (white wash) after chrome plating that result from passive bright nickel deposits. TDS SDS
ACTIVATOR EElectrolytic deoxidizing and descaling of steel and an electrolytic activator for bright nickel electroplated deposits prior to chrome plating. This activator prevents milky films and stains that result from passive bright nickel deposits. TDS SDS
DYNAPREP AS #1Powdered acid salt. Produces a smut-free and active surface on steel, zinc, brass, copper, nickel, aluminum, pewter, Kovar and Invar. Can be used a cathodic electrolyte to effectively remove tenacious oxides, smut and scale.Activating Salts / Additives TDS SDS
DYNAPREP AS #10Economical, powdered acid salt used to replace most mineral acid pickling and activating solutions used in electroplating applications.Activating Salts / Additives TDS SDS
DYNAPREP AS #11Acid salt formulated to descale brass and restore the brass colour after brazing or soldering.Activating Salts / Additives TDS SDS
DYNAPREP AS #12Acid salt formulated to activate alloys containing lead.Activating Salts / Additives TDS SDS
DYNAPREP AS #3Powdered, alkaline activating salt used in the cycle with DYNAFIN 520for the blackening brass and other copper alloys containing less than 90% copper.Activating Salts / Additives TDS SDS
DYNAPREP AS #4Non-fluoride acid salt used to produce a smut-free and active surface on steel, zinc, brass, copper and nickel. Can be used as a cathodic electrolyte to effectively remove tenacious oxides, smut and scale.Activating Salts / Additives TDS SDS
DYNAPREP AS #5Two part powdered product that are dissolved in water to produce a non fuming pickling solution for copper, copper alloys, aluminum and other non-ferrous alloys.Activating Salts / Additives TDS SDS
DYNAPREP AS #6Acid salt used to produce a smut-free and active surface on steel, zinc, brass, copper, nickel, aluminum, pewter, Kovar and Invar.Activating Salts / Additives TDS SDS
DYNAPREP AS #7Fluoride-containing acid salt used in acid treatment and etching of various metals. It can be used to replace hydrofluoric acid, and is much safer to use since it is granular.Activating Salts / Additives TDS SDS
DYNAPREP AS #8Acid salt used to produce an active surface on steel, zinc die castings, brass and copper.Activating Salts / Additives TDS
DYNAPREP AS #9Liquid conditioner / activator used prior to room temperature blackening processes on difficult to blacken surfaces steel, cast iron and leaded steel substrates.Activating Salts / Additives TDS SDS
DYNAPREP BUILDERAlkaline builder package for use with DYNAPREP cleaner surfactant packages to replace the liquid caustic soda for more effective cleaning.Activating Salts / Additives TDS SDS
DYNAPREP BUILDER PHighly alkaline powdered product that is mixed with water to remove rust and oxidation from ferrous metals by immersion. Can be added to a Dynaprep alkaline soak cleaner to clean and de-rust in one step.Activating Salts / Additives TDS SDS
DYNAPREP FCAConcentrated liquid mixture, which is added to hydrochloric or sulphuric acid pickling solutions to reduce the acid fumes without the aid of a foam blanket.Activating Salts / Additives TDS
DYNAPREP IHEffective inhibited acid material mixture, formulated to quickly remove rust, scale and oxides from ferrous metal surfaces without excessive attack of the base metal.Activating Salts / Additives TDS SDS
DYNAPREP INHLiquid mixture, which is added to hydrochloric acid pickling solutions to protect the steel surface, reduce acid wastage, reduce metal loss, prevent pitting and discoloration of the metal surface.Activating Salts / Additives TDS SDS
DYNAPREP INH-2Liquid mixture, which is added to sulphuric acid or hydrochloric acid pickling solutions to protect the steel surface, reduce acid wastage, reduce metal loss, prevent pitting and discolouration of the metal surface.Activating Salts / Additives TDS
DYNAPREP INH-2PLiquid mixture, which is added to sulphuric acid or hydrochloric acid pickling solutions to solubilize oils, protect the steel surface, reduce acid wastage, reduce metal loss, prevent pitting and discoloration of the metal surface.Activating Salts / Additives TDS
DYNAPREP PDConcentrated powdered detergent, which is added to an existing cleaner tank to restore or improve cleaning properties.Activating Salts / Additives TDS
DYNAPREP WALiquid surfactant mixture, which lowers surface tension, reduces fuming, increases detergency and controls oil in acidic and alkaline solutions. Can also be added to Dynamix acid zinc solutions to eliminate the effects of oil contamination.Activating Salts / Additives TDS SDS
DYNAPREP WA-NFAlkylphenols and alkylphenol ethoxylates free liquid surfactant mixture, which lowers surface tension, reduces fuming, increases detergency and controls oil in acidic and alkaline solutions.Activating Salts / Additives TDS SDS
DYNATREAT ACID PUREChemical reagent product that will allow metals, organics and impurities to be filtered out of solution and extend the life of hydrochloric acid, sulphuric acid, nitric acid, citric acid, phosphoric acid, acid salts, acid mixtures.Activating Salts / Additives TDS SDS
DYNAPREP AC #1Phosphoric acid based cleaner for aluminum and aluminum alloys formulated to effectively clean a wide range of soils and leave a mild fine etched surface.Aluminum Pretreatment TDS
DYNAPREP ADChromium free deoxidizer and desmutter for aluminum and aluminum alloys.Aluminum Pretreatment TDS SDS
DYNAPREP AD #2Fluoride and chromium free deoxidizer and desmutter for aluminum and aluminum alloys.Aluminum Pretreatment TDS SDS
DYNAPREP AD #2DConcentrated liquid, fluoride and chromium free deoxidizer and desmutter for aluminum and aluminum alloys. Includes a detergent.Aluminum Pretreatment TDS
DYNAPREP AD #3Liquid, chromium free de-oxidizer and de-smutter for aluminum and aluminum alloys.Aluminum Pretreatment TDS SDS
DYNAPREP AD #3GPowdered, chromium free de-oxidizer and de-smutter for aluminum and aluminum alloys.Aluminum Pretreatment TDS
DYNAPREP AD #6Non-chromated, easy to handle deoxidizer that quickly removes oxides, smut, mill scale and heat treating discoloration from aluminum and a wide variety of its alloys. Brightens stainless steel.Aluminum Pretreatment TDS
DYNAPREP AD #7DPhosphoric acid based cleaner, brightener and pre-paint conditioner for aluminum. Should not be used on high copper bearing aluminum alloys or aluminum castings.Aluminum Pretreatment TDS
DYNAPREP AE #4Liquid, acidic cleaner formulated for a wide range of aluminum alloys, steel, brass, copper and zinc. It provides a mild, uniform etch that can be controlled by adjusting the solution concentration and temperature.Aluminum Pretreatment TDS
DYNAPREP AE 738Liquid, acidic etch formulated to provide a fine matte satin finish on aluminum and aluminum alloys prior to anodizing.Aluminum Pretreatment TDS
DYNAPREP AE 738 DDYNAPREP AE 738 D is a powdered acid etch formulated to provide a fine matte satin finish on aluminum and aluminum alloys prior to anodizing.Aluminum Pretreatment TDS SDS
DYNAPREP AE ADDITIVE #1Aluminum etch additive formulated to prevent sludge and scale while significantly extending the etch bath life.Aluminum Pretreatment TDS SDS
DYNAPREP AE-GPowdered, alkaline enchant for use on aluminum and aluminum alloys. Specially formulated to provide an etch with extra hiding power to help hid die lines and other marks.Aluminum Pretreatment TDS SDS
DYNAPREP AE-G2Powdered, alkaline etch for aluminum and aluminum alloys. Formulated with an inhibitive grain-refining agent for controlled etching, and chelating agents to prevent the formation of aluminum oxide sludge.Aluminum Pretreatment TDS
DYNAPREP ALBONDCyanide based liquid alloy zincate used for producing a zinc immersion coating on properly prepared aluminum and aluminum alloy surfaces.Aluminum Pretreatment TDS SDS
DYNAPREP ALBOND CFCyanide free liquid zincate used for producing a zinc immersion coating on properly prepared aluminum and aluminum alloy surfaces.Aluminum Pretreatment TDS SDS
DYNAPREP ALBOND CF3Cyanide-free, low concentration, liquid zincate process designed to apply a thin zinc film on adequately prepared aluminum alloys.Aluminum Pretreatment TDS SDS
DYNAPREP AS #2Powdered product that is used for stripping zincate from aluminum, deoxidizing aluminum. Can also be used to make a non-chelated, mild etch solution for copper. .Aluminum Pretreatment TDS SDS
DYNAPREP AELow foaming, alkaline aluminum etch designed to reduce build up of scale and sludge, easy to rinse, resulting in low drag out losses.Burnishing Compounds TDS SDS
DYNAPREP BC #5Economical, mildly alkaline burnishing compound for use in barrel and in vibratory machine finishing operations. High luster finish in minimal operating time on copper alloys and precious metals.Burnishing Compounds TDS
DYNAPREP SE300Concentrated liquid surfactant package suitable for both soak and electro cleaning of steel, cast iron and stainless steel. Can be emulsifying or oil splitting depending on caustic level, customer adds own caustic for best economy.Combination Soak / Electro Cleaners TDS SDS
DYNAPREP SE300 NFNonylphenol and nonylphenol ethoxylate free version of DYNAPREP SE300.Combination Soak / Electro Cleaners TDS
DYNAPREP SE350Liquid, heavy duty cleaner suitable for both soak and electro cleaning of steel, cast iron and stainless steel. This is a medium alkalinity, heavy-duty product formulated to be effective with or without reverse electro cleaning.Combination Soak / Electro Cleaners TDS SDS
DYNAPREP SE355Liquid, heavy duty cleaner suitable for both soak and electro cleaning of steel, cast iron and stainless steel. This is a high alkalinity, phosphate free, heavy-duty product formulated to be effective with or without reverse electro cleaning.Combination Soak / Electro Cleaners TDS
DYNAPREP SE400Powdered, mildly alkaline cleaner suitable for both soak and electro cleaning of most substrates including steel, copper, brass and zinc die cast.Combination Soak / Electro Cleaners TDS SDS
DYNAPREP SE401Powdered mildly alkaline soak and electro cleaner for use on both ferrous and non-ferrous metals. Contains a corrosion inhibitor to protect steel, copper and copper alloys when manufacturing operations are performed prior to final coating.Combination Soak / Electro Cleaners TDS
DYNAPREP SE402Phosphate free, concentrated powdered alkaline combination soak and electro cleaner for use on both ferrous and non-ferrous metals.Combination Soak / Electro Cleaners TDS
DYNAPREP SE403Concentrated powdered mildly alkaline combination soak and electro cleaner for use on both ferrous and non-ferrous metals.Combination Soak / Electro Cleaners
DYNAPREP SE550Concentrated powdered mildly alkaline soak and electro cleaner for use on both ferrous and non-ferrous metals, along with cathodic electrocleaning of steel, stainless steel and nickel activation.Combination Soak / Electro Cleaners TDS SDS
DYNAPREP E150Concentrated liquid surfactant package for the electro cleaning of steel, and stainless steel. This is a high alkalinity, non-chelated, heavy-duty electro cleaner formulated to be effective with or without reverse electro cleaning. Customer adds own caustic for best economyElectro Cleaners TDS SDS
DYNAPREP E150 NFLiquid surfactant package for the electro cleaning of steel, and stainless steel.  This is a high alkalinity, non-chelated, heavy-duty electro cleaner formulated to be effective with or without reverse electro cleaning and is nonylphenol and nonylphenol ethoxylate free. Electro Cleaners TDS
DYNAPREP E160 ULTRADYNAPREP E160 ULTRA is a liquid surfactant package for the electro cleaning of steel parts with excellent oil and smut removal.  This is a high alkalinity, chelated, heavy-duty electro cleaner.Electro Cleaners TDS SDS
DYNAPREP E170 DSDYNAPREP E170 DS is a heavy duty, powdered, alkaline descaler designed to remove heat treat scales and rust from ferrous substrates and stains from copper and its alloys. DYNAPREP E170 DS can also be used to strip paint with or without current, remove smut after pickling and as a cathodic activator for nickel.Electro Cleaners TDS
DYNAPREP E450Heavy duty, powdered, alkaline electro cleaner designed for steel, and stainless steel.  Dynaprep E450 is a high alkalinity, non-chelated and non-emulsifying electro cleaner formulated to be effective for direct, or reverse current electro cleaning.  Dynaprep E450 does not containalkylphenols nor alkylphenol ethoxylates.Electro Cleaners TDS SDS
DYNAPREP E451Heavy duty, powdered, alkaline electro cleaner designed for steel, and stainless steel.  Dynaprep E451 is a high alkalinity, non-chelated and non-emulsifying electro cleaner formulated to be effective for direct, or reverse current electro cleaning.  Dynaprep E451 does not containNonylphenols and is octylphenol free.Electro Cleaners TDS SDS
DYNAPREP ELECTRO #2Heavy duty, powdered, high alkalinity, non chelated, non-emulsifying electro cleaner designed for steel, and stainless steel.   DYNAPREP ELECTRO #2 has a long standing reputation as a great electrocleaner for critical cleaning applications such as bright nickel plating lines.Electro Cleaners TDS
DYNAPREP ELECTRO #3Heavy duty, powdered, alkaline electro cleaner designed for steel, and stainless steel.  DYNAPREP ELECTRO #3 is a phosphate free, high alkalinity, non-chelated and non-emulsifying electro cleaner formulated to be effective for direct, or reverse current electro cleaning. Electro Cleaners TDS
DYNAPREP BCRConcentrated, powdered, low alkalinity soak cleaner used for the removal of buffing compounds from both ferrous and non-ferrous metals.Soak Cleaners TDS
DYNAPREP DS 520DYNAPREP DS 520 is a heavy duty, liquid, alkaline descaler designed to remove heat treat scales and rust from ferrous substrates.  DYNAPREP DS 520 can also be used to strip some types of enamels and performs well as an electro cleaner. FEATURES:• Cyanide and phosphate free.• Minimal hydrogen embrittlement.• Excellent with or without current to remove light scale, rust, phosphate coatings, oxides, oil, grease, paint and smut.• Prevents scale build-up on tank walls and heating coils.• High conductivity for maximum gassing and cleaning effect.• Not sensitive to hard water.• Does not attack mild steel substrates.• Superior rinsing properties minimizing drag-out loses.Soak Cleaners TDS SDS
DYNAPREP GPCCaustic soda and phosphate free concentrated heavy-duty liquid citrus-based cleaner for use as a general purpose cleaner on concrete and tiled surfaces. Very effective at removing tough soils, grease, oil etc from shop floors, tiled floors, machines and other hard surfaces.Soak Cleaners TDS SDS
DYNAPREP GPSPhosphate free concentrated heavy-duty liquid detergent for use as a general purpose cleaner on concrete and tiled surfaces. Very effective at removing tough soils, grease, oil etc from shop floors, tiled floors, machines and other hard surfaces.Soak Cleaners TDS SDS
DYNAPREP HDCConcentrated surfactant package blended with alkaline builders to provide a soak cleaner with excellent detergency and an electro cleaner with superior conductivity.Soak Cleaners TDS
DYNAPREP S100Concentrated liquid surfactant package for the soak cleaning of steel, stainless steel and leaded steel. This is a high alkalinity, non-chelated, heavy-duty soak cleaner formulated to be effective in hard water areas. Can be emulsifying or oil splitting depending on caustic level, customer adds own caustic for best economy. Dynaprep S100 is Nonyl Phenol (NP) and Nonyl Phenol Ethoxylate (NPE) free.Soak Cleaners TDS SDS
DYNAPREP S110Liquid surfactant package for the soak cleaning of steel, stainless steel, leaded steel and aluminum.  This is a high alkalinity, heavy-duty soak cleaner formulated to be effective in hard water areas.  Nonylphenol and nonylphenol ethoxylate free.Soak Cleaners TDS SDS
DYNAPREP S130 SSUnique powdered alkaline blend specifically developed to remove all types of soils from Stainless Steel.  The specific wetting agents provide fast wetting and contribute to the dispersion and loosening of soils and dirt.    Suitable for use on all stainless steels, copper, brass and ferrous substrates.Soak Cleaners TDS SDS
DYNAPREP S200Powdered high-performance, non-etch, non-silicated, non-caustic, alkaline soak cleaner that is very effective in removing soils and lubricants from aluminum surfaces. Dynaprep S200 does not leave a difficult to remove film typical non-etch cleaners and is also suitable for use as a multi-metal soak cleaner for all substrates including zinc die-cast.Soak Cleaners TDS SDS
DYNAPREP S201High detergent, mildly alkaline, emulsifying, non-etch soak cleaner for aluminum. Since Dynaprep S201 does not contain silicates, no residual siliceous films remain to cause a non-uniform appearance after electroless nickel plating.  Dynaprep S201 contains no EDTA, providing a waste treatment friendly product. At recommended concentration, and temperature Dynaprep S201 will not etch aluminum.Soak Cleaners TDS
DYNAPREP S202 Low foaming version of Dynaprep S200  Soak Cleaners TDS
DYNAPREP S237-USDYNAPREP S237-USis a mildly alkaline Immersion cleaner with good emulsifying characteristics, for the cleaning of copper and aluminum alloys.DYNAPREP S237-UScan also be successfully used as an ultrasonic cleaner for the removal of polishing paste residue from brass surfaces.Soak Cleaners TDS SDS
DYNAPREP S250Heavy duty, concentrated powdered alkaline soak cleaner for use on steel, zinc die-cast, copper and brass.  Dynaprep S250 is non-chelated and non-emulsifying.Soak Cleaners TDS SDS
DYNAPREP S250 NPFHeavy duty, concentrated powdered alkaline soak cleaner for use on steel, zinc die-cast, copper and brass. Dynaprep S250-NPF is non-chelated, non-emulsifying,does not containnonylphenols and is octylphenol free.Soak Cleaners TDS
DYNAPREP S260Dynaprep S260 is a heavy duty, concentrated, powdered, high alkalinity soak cleaner for use on steel, stainless steel and leaded steel.  Dynaprep S260 is an oil-splitting cleaner that is effective at removing most soils including water-soluble oils, mineral oils, drawing compounds and buffing compounds.  Dynaprep S260 does not contain alkylphenols nor alkylphenol ethoxylates.Soak Cleaners TDS SDS
DYNAPREP S270Heavy duty, concentrated, powdered, high alkalinity soak cleaner for use on steel, stainless steel and leaded steel.  Dynaprep S270 is an emulsifying cleaner that is effective at removing most soils including water-soluble oils, mineral oils and drawing.Soak Cleaners TDS SDS
DYNAPREP S280DYNAPREP S280 is a concentrated liquid acidic soak cleaner / conditioner for use on ferrous metals, aluminum, zinc, copper, copper alloys and stainless steel.   This cleaner will remove light oils, rust, rust, heat scale, weld scale and oxides as well as condition ferrous, aluminum and zinc surfaces into a metal-phosphate surface which serves as a paint base.Soak Cleaners TDS
DYNAPREP S281Concentrated liquid acidic soak cleaner for use on steel parts prior to galvanizing.   Soak Cleaners TDS
DYNAPREP S290Dynaprep S290 is a multi-purpose, heavy duty, concentrated, powdered, high alkalinity immersion soak cleaner for ferrous metal.  Dynaprep S290 is an emulsifying cleaner that is effective at removing most soils including heavily chlorinated and sulphurized oils, fats, and coolants from metal substrates.  Its unique formulation allows complete lifting of soils and emulsification of oils, reducing residuals on washed parts.Soak Cleaners TDS
DYNAPREP S291Heavy duty, concentrated, powdered, high alkalinity soak cleaner for use on steel, stainless steel and leaded steel. Dynaprep S291 is an emulsifying cleaner that is effective at removing most soils including water-soluble oils, mineral oils and drawing. Soak Cleaners TDS
DYNAPREP S500Dynaprep S500 is a non-caustic, concentrated powdered alkaline soak cleaner for use on steel, zinc die-cast, copper, brass and aluminum.  Dynaprep S500 is non-chelated and is an excellent choice for difficult to remove soils in short cleaning cycles.  Soak Cleaners TDS SDS
DYNAPREP S500ADynaprep S500A is a non-caustic, concentrated powdered alkaline soak cleaner for use on steel, zinc die-cast, copper, brass and aluminum.  Dynaprep S500A is non-chelated and is an excellent choice for difficult to remove soils in short cleaning cycles.  Soak Cleaners TDS
DYNAPREP S600Dynaprep S600 is a mildly alkaline, concentrated powdered soak cleaner formulated for removing buffing compounds from steel, zinc die-cast, copper, brass and aluminum.Soak Cleaners TDS
DYNAPREP DCTwo component, alkaline, heavy duty, low foaming immersion or spray cleaner for use on ferrous metals. Dynaprep DC will provide effective cleaning of soils including heavily chlorinated, sulphurized oils, fats, coolants, buffing compounds and drawing compounds.Spray Cleaners TDS
DYNAPREP SP140Concentrated liquid product, designed for use as an immersion or spray cleaner for ferrous metal substrates.  DYNAPREP SP140 provides effective removal of drawing compounds, heavily chlorinated, sulphurized oils, fats, coolants and dry film lubricants.Spray Cleaners TDS SDS
DYNAPREP SP140 NF Concentrated liquid product, designed for use as an immersion or spray cleaner for ferrous and non-ferrous metal substrates.  DYNAPREP SP145 provides effective removal of drawing compounds, heavily chlorinated, sulphurized oils, fats, coolants and dry film lubricants.Spray Cleaners TDS SDS
DYNAPREP SP145Concentrated liquid potash-based product, designed for use as an immersion or spray cleaner for ferrous metal substrates.  DYNAPREP SP145 is a low-foaming product that provides effective removal of soils, including heavily chlorinated and sulphurized oils, fats and coolants.  It offers good tramp oil rejection, fines settling, is easily filtered, and allows complete lifting of soils without emulsification of oils, allowing the free oils to be removed by weir or skimmer.Spray Cleaners TDS
DYNAPREP SP295Dynaprep SP295 is a multi-purpose, heavy duty, concentrated, powdered cleaner formulated for use as immersion or spray cleaner for all metals including aluminum.  Dynaprep SP295 provides safe, effective removal of manufacturing soils, including heavily chlorinated and sulphurized oils, fats and coolants from metal substrates.Spray Cleaners TDS SDS
DYNAPREP SP366Potash-based, phosphate-free,multi-purpose, heavy duty, concentrated, liquid cleaner formulated for use as an immersion or spray cleaner for ferrous metals.  Dynaprep SP366 provides safe, effective removal of manufacturing soils, including heavily chlorinated and sulphurized oils, fats and coolants from metal substrates.Spray Cleaners TDS
DYNAPREP SSEHigh detergency, low foaming and concentrated liquid alkaline product for use as an immersion, spray or electro cleaner for ferrous metal substrates.  DYNAPREP SSE provides effective removal of drawing compounds, heavily chlorinated, sulphurized oils, fats, and coolants.Spray Cleaners TDS
DYNAPREP US No.1Concentrated, caustic-free liquid formulated for use as an ultrasonic cleaner. Non-ionic surfactants, wetting agents, dispersants and deflocculents are combined to provide excellent detergency and free rinsing properties. DYNAPREPUS #1 provides exceptional performance for virtually all base metals.Spray Cleaners TDS SDS

Electroplating Processes

Product NameSummaryCategoryTech Data SheetSafety Data Sheet
DYNATREAT DEFOAMER #3Specially formulated defoamer for use in DYNAPLATE CLZ chloride zinc process. TDS SDS
DYNAPLATE CADConcentrated liquid addition agent for producing bright, fine grained cyanide cadmium electroplated deposits.Cadmium TDS SDS
DYNAPLATE NC-CADDynaplate NC-CAD is a non-cyanide process for electroplating bright, fine-grained cadmium deposits.  The process is suitable for both rack and barrel operations.Cadmium TDS SDS
DYNAPLATE Cr CCHigh efficiency mixed catalyst system utilizing a single liquid catalyst in conjunction with Chromic Acid and Sulphuric Acid, suitable for use in functional applications.Chrome TDS
DYNAPLATE Cr CLSpecially formulated blend of Chromic Acid and secondary Fluoride catalyst for decorative and hard chrome plating. Liquid version.Chrome TDS SDS
DYNAPLATE Cr CPSpecially formulated blend of Chromic Acid and secondary Fluoride catalyst for decorative and hard chrome plating. Powdered version.Chrome TDS
DYNAPLATE Cr CTRHigh efficiency, easy to control triple catalyst system for chrome plating. Providing significant improvement over mixed catalyst systems.Chrome TDS
DYNAPLATE Cr DFPFAS and Fluoride free liquid defoamer product developed to eliminate foam in Hexavalent Chromium plating solutions. Typically used with Dynaplate Cr FSN2 fume suppressant.Chrome TDS SDS
DYNAPLATE Cr ESSelf-regulating hard chromium plating solution.Chrome TDS SDS
DYNAPLATE Cr FSPFOS free mist suppressant for hexavalent chromium plating solutions.Chrome TDS SDS
DYNAPLATE Cr FSLLow foaming PFOS free mist suppressant used in hexavalent chromium plating solutions to control misting and reduce ventilation requirement.Chrome TDS SDS
DYNAPLATE Cr FSNPFOS, PFAS and fluoride free fume suppressant used in hexavalent chromium plating solutions to control misting and reduce ventilation requirement.Chrome TDS SDS
DYNAPLATE Cr HSHigh Speed Functional Chromium Plating Process. Fluoride-free and etch-free.Chrome TDS
DYNAPLATE Cr HS CHigh Speed Functional Chromium Plating Process. Fluoride-free and etch-free. Catalyst Component.Chrome SDS
DYNAPLATE Cr HS MLHigh Speed Chromium plating solution. Make-Up Solution.Chrome SDS
DYNAPLATE Cr HS MPHigh Speed Chromium plating solution. Customer specific Make-Up Solution.Chrome SDS
DYNAPLATE Cr HS RLHigh Speed Chromium plating solution. Replenishment Solution.Chrome SDS
DYNAPLATE Cr HS RPHigh Speed Chromium plating solution. Customer Specific Replenishment Solution.Chrome SDS
DYNAPLATE Cr SFSelf regulating hard Chromium plating solution.Chrome TDS SDS
DYNAPLATE Cr-HSDYNAPLATE Cr-HS is a specially formulated High Speed Functional Chromium electroplating process which is fluoride free. Chrome TDS SDS
DYNAPLATE CrCHigh speed Hex Chromium plating catalyst. Liquid form.Chrome TDS SDS
DYNAPLATE CrCHigh speed Hex Chromium plating catalyst. Liquid form.Chrome
DYNAPLATE TBCrBlack trivalent chrome plating process developed to meet the needs of an environmentally safer process than the existing chromic acid based processes. Chrome TDS
DYNAPLATE TrCTrivalent chrome plating process developed to meet the needs of an environmentally safer process than the existing chromic acid based processes.Chrome TDS SDS
DYNATREAT LACUsed for the removal of lead anode films and scales which can form on lead anodes in hexavalent chromium solutions. Complies with BAC5709.Chrome TDS SDS
DYNAPLATE AC-DSingle additive bright acid copper plating process with high levelling and formulated specifically for higher current density plating.Copper / Copper Alloys TDS SDS
DYNAPLATE AC-SUltra-high performance, dye-free addition agent system for bright acid copper plating, which produces exceptionally bright, ductile deposits with low internal stress.Copper / Copper Alloys TDS SDS
DYNAPLATE CARBONATE REDUCERPowdered additive used for the fast precipitation and reduction of carbonates from cyanide electroplating solutions.Copper / Copper Alloys TDS SDS
DYNAPLATE CNC BThis product is part of a collection of products that make up DYNAPLATE CNC-AC. This is the Brightener Component.Copper / Copper Alloys SDS
DYNAPLATE CNC FS DYNAPLATE CNC FS is used to reduce the surface tension of cyanide brass and copper plating solutions that utilize mechanical agitation. It improves surface contact with the plating solution, and reduces drag out.Copper / Copper Alloys TDS
DYNAPLATE CNC WETTERThis product is part of a collection of products that make up DYNAPLATE CNC-AC. This is the Wetter Component.Copper / Copper Alloys SDS
DYNAPLATE EN 1000 AThis product is part of a collection of products that make up DYNAPLATE EN 1000. Semi-Bright, Low Phosphorous Electroless Nickel Process. This is the A component.Electroless Nickel
DYNAPLATE EN 1000 BThis product is part of a collection of products that make up DYNAPLATE EN 1000. Semi-Bright, Low Phosphorous Electroless Nickel Process. This is the B componentElectroless Nickel
DYNAPLATE EN 1000 CThis product is part of a collection of products that make up DYNAPLATE EN 1000. Semi-Bright, Low Phosphorous Electroless Nickel Process. This is the C componentElectroless Nickel
DYNAPLATE EN 6000 AThis product is part of a collection of products that make up DYNAPLATE EN 6000. Bright, Medium Phosphorous High Speed Electroless Nickel Process. This is the A componentElectroless Nickel
DYNAPLATE EN 6000 BThis product is part of a collection of products that make up DYNAPLATE EN 6000. Bright, Medium Phosphorous High Speed Electroless Nickel Process. This is the B componentElectroless Nickel
DYNAPLATE EN 6000 CThis product is part of a collection of products that make up DYNAPLATE EN 6000. Bright, Medium Phosphorous High Speed Electroless Nickel Process. This is the C componentElectroless Nickel
DYNAPLATE EN 6000 RC AThis product is part of a collection of products that make up DYNAPLATE EN 6000 RC. RoHS Compliant, Bright, Medium Phosphorous High Speed Electroless Nickel Process. This is the A componentElectroless Nickel
DYNAPLATE EN 6000 RC BThis product is part of a collection of products that make up DYNAPLATE EN 6000 RC. RoHS Compliant, Bright, Medium Phosphorous High Speed Electroless Nickel Process. This is the B componentElectroless Nickel
DYNAPLATE EN 6000 RC CThis product is part of a collection of products that make up DYNAPLATE EN 6000 RC. RoHS Compliant, Bright, Medium Phosphorous High Speed Electroless Nickel Process. This is the C componentElectroless Nickel
DYNAPLATE EN 6500RoHS Compliant, ONE COMPONENT, Bright, Medium Phosphorous, High-Speed Electroless Nickel Process.Electroless Nickel TDS SDS
DYNAPLATE EN 9000 AThis product is part of a collection of products that make up DYNAPLATE EN 9000. Semi-Bright, High Phosphorous Electroless Nickel Process. This is the A component.Electroless Nickel
DYNAPLATE EN 9000 BThis product is part of a collection of products that make up DYNAPLATE EN 9000. Semi-Bright, High Phosphorous Electroless Nickel Process. This is the B component.Electroless Nickel
DYNAPLATE EN 9000 CThis product is part of a collection of products that make up DYNAPLATE EN 9000. Semi-Bright, High Phosphorous Electroless Nickel Process. This is the C component.Electroless Nickel
DYNAPLATE EN ALBOND AThis product is part of a collection of products that make up DYNAPLATE EN ALBOND. Electroless Nickel Barrier Coating for Aluminum. This is the A component.Electroless Nickel
DYNAPLATE EN ALBOND BThis product is part of a collection of products that make up DYNAPLATE EN ALBOND. Electroless Nickel Barrier Coating for Aluminum. This is the B component.Electroless Nickel
DYNAPLATE EN ALBOND CThis product is part of a collection of products that make up DYNAPLATE EN ALBOND. Electroless Nickel Barrier Coating for Aluminum. This is the C component.Electroless Nickel
DYNAPLATE Ni AWThis product is part of a collection of products that make up DYNAPLATE Ni. Bright Nickel Plating System. This is the Air Wetter component used to reduce surface tension.Nickel SDS
DYNAPLATE Ni BThis product is part of a collection of products that make up DYNAPLATE Ni. Bright Nickel Plating System. This is the Brightener component used for makeup and replenishment.Nickel SDS
DYNAPLATE Ni BOOSTERThis product is part of a collection of products that make up DYNAPLATE Ni. Bright Nickel Plating System. This is a Booster component used when higher levels of brightness and levelling must be obtained in reduced plating times.Nickel SDS
DYNAPLATE Ni CThis product is part of a collection of products that make up DYNAPLATE Ni. Bright Nickel Plating System. This is the carrier component used for makeup and periodic replenishment.Nickel SDS
DYNAPLATE Ni LBThis product is part of a collection of products that make up DYNAPLATE Ni L. Fast Levelling Bright Nickel Plating System. This is the brightener component used for makeup and replenishment.Nickel SDS
DYNAPLATE Ni MWThis product is part of a collection of products that make up DYNAPLATE Ni L. Fast Levelling Bright Nickel Plating System. This is the mechanical wetter component used for barrel or mechanically agitated solutions.Nickel SDS
DYNAPLATE Ni PThis product is part of a collection of products that make up DYNAPLATE Ni L. Fast Levelling Bright Nickel Plating System. This is the purifier component used to correct non-ferrous metallic contamination.Nickel SDS
DYNAPLATE SB-NiBThis product is part of a collection of products that make up DYNAPLATE SB Ni. Semi-Bright Nickel Plating System. This is the brightener component used for makeup and replenishment.Nickel SDS
DYNAPLATE SB-NiMThis product is part of a collection of products that make up DYNAPLATE SB Ni. Semi-Bright Nickel Plating System. This is a levelling component used for makeup and periodic replenishment.Nickel SDS
DYNAPLATE ISn Stable liquid process that deposits a thin, bright uniform immersion tin over copper and copper alloys. The deposited tin promotes solderability and inhibits oxidation of the substrate.Tin TDS
DYNAPLATE ITP Immersion tin process for coating properly prepared aluminum and aluminum alloy surfaces.Tin TDS SDS
DYNAPLATE Sn MatteDYNAPLATE Sn Matte is a high-speed matte acid tin system for rack and barrel plating that will deposit a smooth, white, and ductile deposit with excellent solderability.Tin SDS
DYNAPLATE Sn-RAAdditive used in tin post plate rinses to eliminate stains and improve solderability of the deposit.Tin TDS SDS
DYNAPLATE SnBThis product is part of a collection of products that make up DYNAPLATE SnB. Bright Acid Tin Plating System. This is a brightener component used for makeup and replenishment.Tin SDS
DYNAPLATE SnMThis product is part of a collection of products that make up DYNAPLATE SnB. Bright Acid Tin Plating System. This is a levelling component used for makeup.Tin SDS
DYNAPLATE SnPAdditive used to precipitate Stannic Tin.Tin TDS SDS
DYNAPLATE CLZNewest generation, extremely bright, water soluble and ductile chloride zinc system for rack and barrel plating.Zinc TDS SDS
DYNAPLATE CPPurifier used to precipitate heavy metal impurities in cyanide cadmium and zinc plating baths.Zinc SDS
DYNAPLATE CZCyanide Zinc plating system with a general-purpose brightener system for use in low to high cyanide zinc plating solutions.Zinc SDS
DYNAPLATE NCZ BThis product is part of a collection of products that make up DYNAPLATE NCZ. Alkaline Non-Cyanide Zinc Plating System. This is the brightener component used for makeup and replenishment.Zinc SDS
DYNAPLATE NCZ CThis product is part of a collection of products that make up DYNAPLATE NCZ. Alkaline Non-Cyanide Zinc Plating System. This is the carrier component used for makeup and replenishment.Zinc SDS
DYNAPLATE NCZ CARBONATE REDUCERPowdered additive used for the fast precipitation and reduction of carbonates from cyanide and non-cyanide electroplating solutions. It reduces carbonates without increasing the cyanide but, the alkalinity of the electroplating process will increase. Excessive carbonates in an electroplating solution can result in lower efficiency, roughness, anode polarization, high chemical and additive consumption.Zinc TDS
DYNAPLATE NCZ PThis product is part of a collection of products that make up DYNAPLATE NCZ. Alkaline Non-Cyanide Zinc Plating System. This is the purifier component used to reduce deposit cloudiness from dragged in contaminants.Zinc SDS
DYNAPLATE CL ZnNi-BThis product is part of a collection of products that make up DYNAPLATE CL ZnNi. Zinc Nickel Alloy Plating System. This is the brightener component used for makeup and replenishment.Zinc Alloy SDS
DYNAPLATE CL ZnNi-CThis product is part of a collection of products that make up DYNAPLATE CL ZnNi. Zinc Nickel Alloy Plating System. This is the carrier component used for makeup and replenishment.Zinc Alloy SDS
DYNAPLATE NCZ Co ADDITIVEThis product is part of a collection of products that make up DYNAPLATE NCZ-Co. Alkaline Zinc-Cobalt Alloy Plating System. This is an additive used to maintain the concentration of Cobalt in solution.Zinc Alloy
DYNAPLATE NCZ CoBThis product is part of a collection of products that make up DYNAPLATE NCZ-Co. Alkaline Zinc-Cobalt Alloy Plating System. This is the brightener component used for make up and replenishment.Zinc Alloy
DYNAPLATE NCZ CoCThis product is part of a collection of products that make up DYNAPLATE NCZ-Co. Alkaline Zinc-Cobalt Alloy Plating System. This is the carrier component used for make up and replenishment.Zinc Alloy
DYNAPLATE NCZ COMPLEXORThis product is part of a collection of products that make up DYNAPLATE NCZ-Co. Alkaline Zinc-Cobalt Alloy Plating System. This is the component used to maintain the solubility of the cobalt and control its distribution.Zinc Alloy SDS
DYNAPLATE NCZ CONDITIONERThis product is part of a collection of products that make up DYNAPLATE NCZ-Co. Alkaline Zinc-Cobalt Alloy Plating System. This is the water softening component used to reduce smokiness in the deposit.Zinc Alloy SDS
DYNAPLATE NCZ Fe ADDITIVEThis product is part of a collection of products that make up DYNAPLATE NCZ-Co. Alkaline Zinc-Cobalt Alloy Plating System. This is an Iron controlling and maintaning additive.Zinc Alloy
DYNAPLATE NCZ FeBThis product is part of a collection of products that make up DYNAPLATE NCZ FeB. Alkaline Zinc-Iron Alloy Plating System. This is the brightener component used for make up and replenishment.Zinc Alloy
DYNAPLATE NCZ FeCThis product is part of a collection of products that make up DYNAPLATE NCZ FeB. Alkaline Zinc-Iron Alloy Plating System. This is the carrier component used for make up and replenishment.Zinc Alloy

Electropolishing and Bright Dips

Product NameSummaryCategoryTech Data SheetSafety Data Sheet
DYNABRITE 8538Non-chrome, liquid material that is added to phosphoric acid to create a stable electropolishing solution for stainless steel. TDS SDS
DYNABRITE 8538 CONCENTRATENon-chrome, liquid material that is added to phosphoric acid and sulphuric acid to create a stable electropolishing solution for stainless steel. TDS SDS
DYNABRITE 8538 RTUNon-chrome, liquid stable electropolishing solution for stainless steel. TDS SDS
DYNABRITE 8539Non-chrome, liquid material that is added to phosphoric acid to create a stable electropolishing solution for aluminum. TDS SDS
DYNABRITE 8588Non-chrome, liquid material that is added to phosphoric acid and sulfuric acid to create a stable electropolishing solution for mild steel. TDS SDS
DYNAFIN 5504Liquid product used full strength to polish and passivate stainless steel. TDS SDS
DYNAFIN ALBFluoride based, non-chrome, acidic liquid concentrate formulated for cleaning and brightening/desmutting most aluminum surfaces. TDS SDS
DYNAFIN CAPPowdered chrome containing material for producing lustrous finishes on copper and its alloys. Dynafin CAP will passivate the surface and provide resistance to corrosion, staining, and tarnishing. TDS SDS
DYNAFIN CAP-NCLiquid, non-chrome containing material for producing lustrous finishes on copper and its alloys. Dynafin CAP-NC will passivate the surface and provide resistance to corrosion, staining, and tarnishing. TDS SDS
DYNAFIN FERoom temperature, immersion process designed to brighten carbon steel surfaces. Dynafin FE can also be used to deburr or to remove surface imperfections. TDS SDS
DYNAFIN FE-LLiquid room temperature, immersion process designed to brighten carbon steel surfaces. Dynafin FE-L can also be used to deburr or to remove surface imperfections. TDS SDS
DYNAFIN SSPLiquid blend of chemicals that is diluted with water to clean and passivate most grades of stainless steel, including austenitic, martensitic, and precipitation hardened. TDS SDS
DYNAFIN ZNAcidic, chromate free product used to chemically polish, brighten and condition the zinc die cast surface for subsequent finishing. Also effective to deburr or remove surface imperfections. TDS SDS

Galvanizing & Miscellaneous Products

Product NameSummaryCategoryTech Data SheetSafety Data Sheet
DYNACOAT #6DYNACOAT #6 provides a clear, hard colorless film that prevents white rust and staining on zinc galvanized steel surfaces during storage. Will not interfere with subsequent welding or soldering operations.Galvanizing TDS SDS
DYNAGALV AS DYNAGALV ASis an additive that is added to zinc and ammonium chloride galvanizing fluxes to promote bonding and eliminate explosions when entering the molten zinc bath.   FEATURES·        Reduces zinc consumption by eliminating splatter.·        Increases operator safety. ·        Increases productivity by improving shedding of the flux solution. ·        Reduces labour involved in resurfacing of galvanized parts. ·        Reduces ash and smoke. ·        Reduces flux consumption. ·        Improves surface quality and uniformity of galvanized work.  Galvanizing TDS SDS
HOT-DIP GALVANIZING PRE-FLUXGalvanizing pre-fluxes, or dry kettle galvanizing fluxes, are used to dissolve any oxide films and impurities which are formed on the steel surface after pickling, but before galvanizing. Fluxes also ensure that a wettable and clean metal surface will come in contact with the molten zinc metal.  FLUX TYPEACNCOMMON USEMono Salt 0.39Galvanizing sheet drying oven requiredDouble Salt0.79Galvanizing pipe, drying oven requiredTriple Salt1.17Basic galvanizing flux used in North AmericaQuadraflux1.6General purpose fluxGalvanizing TDS
DYNA-SHED No.1 Used in final hot water rinses to promote water shedding. Can also be added to hydrochloric or sulphuric acid dips and alkaline processes such as electrolytic chromium strippers to reduce drag-out and is suitable for use on all metals.Miscellaneous TDS
DYNAFIN SR-1Simple method for the removal of certain oxide type stains from plated nickel and/or ferrous or stainless steel surfaces. There is virtually no attack of the surface and proper use should help to protect the surface from further staining.  May be used in the post-plate cycle or after the appearance of staining.Miscellaneous TDS SDS
DYNALUBEFormulated from a lithium complex stearate thickener and highly refined, high viscosity stock. It is fortified with oxidation, rust and corrosion inhibitors to extend the service life and protect metal surfaces from rust and etching. This makes it ideal for use in many plating applications including connections, barrel and rack contacts, saddles, flight bars etc.Miscellaneous TDS SDS
DYNAPLATE STOP OFF #2Dynaplate Stop-Off #2is a liquid maskant used as a stop-off for electroless nickel plating, hard coat anodizing, chrome plating, chemical milling, conversion coating and acid solutions. The cured film is tack-free and will not adhere to itself or other parts. Dynaplate Stop-Off #2provides physical protection against surface damage, abrasion and provides a high degree of protection against acid and alkaline attack.  It is a very easy way to apply a strippable coating for the protection of substrates from scratching and marring during handling and long term storage.Miscellaneous TDS
DYNASHED #2liquid additive that can be used in spray and immersion applications to improve water shedding. This rinse aid counter-acts the effects of hard water usually present in city water and provides a uniform rinse run down and drying without hard water spots.Miscellaneous TDS SDS

Sealers and Top Coats

Product NameSummaryCategoryTech Data SheetSafety Data Sheet
DYNACOAT # 1Clear inorganic sealer that will enhance the corrosion resistance of chromated zinc and zinc alloys, along with nickel, steel, and chrome. TDS SDS
DYNACOAT # 2Enhances the corrosion resistance of chromated zinc and zinc alloys, along with nickel, steel, and chrome. The thin, uniform, water-repellent barrier coating will repel humidity and salt spray mist and provide superior corrosion protection. TDS SDS
DYNACOAT # 3Water based clear, high gloss, acrylic finish. Contains no organic solvents. The cured finish will not dissolve in water and the resulting finish has good resistance to scuffing and scratching. TDS SDS
DYNACOAT # 4Water based clear, medium gloss, acrylic finish. Contains no organic solvents. The cured finish will not dissolve in water and the resulting finish has good resistance to scuffing and scratching. TDS
DYNACOAT 215 WAXRust preventative that is applied to black oxide, phosphate and bare steel.  The resulting film will not rub off, has excellent adhesion, is extremely thin, waxy, dry-to-the-touch and offers excellent corrosion protection.    TDS SDS
DYNACOAT DFLUnique, water-based emulsion wax coating suitable for use as a corrosion preventive and decorative coating on steel, phosphated surfaces, anodized surfaces along with all types of plating, including cadmium and zinc. TDS SDS
DYNACOAT OSHigh performance organic sealer that provides a hard clear finish that will enhance the corrosion resistance of chromated zinc and zinc alloys, along with nickel, steel, and chrome. TDS SDS
DYNACOAT OS #2Organic sealer providing a hard clear finish that will enhance the corrosion resistance of chromated zinc and zinc alloys, along with nickel, steel, and chrome. Coefficient of friction on electroplated zinc coatings between 0.16-0.19. TDS SDS
DYNACOAT ST#5Liquid dispersion of organic polymers chemically bonded with inorganic nanoparticles which will enhance the corrosion resistance of trivalent passivation, along with trivalent black as well as hexavalent yellow and olive drab chromates. TDS
DYNACOAT TnTConcentrated, water soluble, liquid product that is used to modify the lubricity of zinc and trivalent chromate coated fasteners. TDS SDS
DYNACOAT WSClear, medium gloss hard drying emulsion wax coating that is applied to metal surfaces. The resulting film will not rub off, has excellent adhesion, is ductile and offers good corrosion protection. TDS SDS
DYNAFIN CI #1Corrosion inhibitor used for protecting steel, nickel, aluminum, copper and copper alloys. Helps reduce staining and increases lubricity. Can also be used in burnishing operations. TDS SDS
DYNAFIN CI #2Liquid, chrome free, phosphate free corrosion inhibitor for zinc, ferrous metals and iron, zinc or manganese modified phosphate coatings. TDS SDS
DYNAFIN CI #3Liquid, chrome free, corrosion inhibitor for un-plated areas on ferrous substrates following nickel and chromium plating. TDS SDS
DYNAFIN CI #4Light duty corrosion inhibitor for most metals. It leaves a dry, invisible film which will not interfere with subsequent finishing operations. DYNAFIN CI No.4 can also be used in burnishing operations. TDS
DYNAFIN CI #5Liquid, chrome free, corrosion inhibitor for un-plated areas on ferrous substrates following nickel and chromium plating. The final seal leaves a clear water-repellent film that will not stain deposits after drying. TDS
DYNAFIN PTFE-60PTFE coating on aluminum surfaces where high lubricity is required. TDS
DYNAFIN WDWater displacing, non-staining rust preventive which will separate water from metal surfaces after machining or cleaning. The films are dry-to-touch and are effective in the protection of ferrous and non-ferrous metals from atmospheric corrosion. TDS SDS
DYNAFIN WD #2Outstanding water displacing, non-staining rust preventive which will separate water from metal surfaces after machining or cleaning. The films are dry-to-touch and protect ferrous and non-ferrous metals from atmospheric corrosion. TDS SDS

Stripping Products

Product NameSummaryCategoryTech Data SheetSafety Data Sheet
DYNASTRIP ACSNon-chrome, liquid material that will remove anodic films from aluminum by immersion without attacking the aluminum surface. TDS SDS
DYNASTRIP CrSpecially formulated, powdered alkaline compound that is used to electrolytically strip chromium from steel and nickel substrates, without attacking the base metal.   TDS SDS
DYNASTRIP Cr-2Specially formulated, powdered alkaline compound that is used to electrolytically strip chromium from steel and nickel substrates, without attacking the base metal. Will strip copper, most copper alloys, zinc and cadmium anodically. TDS SDS
DYNASTRIP DSPUnique combination of methylene chloride and accelerators to effectively strip accumulated paint and overspray from metal substrates. Recommended for use on steel and aluminum, but not recommended for zinc or magnesium. TDS SDS
DYNASTRIP HS ACCELERATORLiquid additive for use with hot alkaline stripping solutions to accelerate the paint and ink removal from ferrous parts. TDS SDS
DYNASTRIP HTHigh temperature paint stripper designed for non-ferrous substrates but will work very well on ferrous as well. TDS SDS
DYNASTRIP MMSpecially formulated powder that is used with sodium cyanide or caustic soda to strip nickel, copper, zinc, tin, tin-lead, brass, cadmium, and silver from steel, copper, brass and magnesium substrates without attacking the base metal. TDS SDS
DYNASTRIP NiSpecially formulated powder that when mixed with water, will provide a safe, immersion solution to strip nickel deposits from ferrous non ferrous substrates without attacking the base metal. TDS SDS
DYNASTRIP Ni-CuDynastrip Ni-Cu is a specially formulated powder that when mixed with water, will provide a safe, immersion solution to strip nickel deposits from copper substrates without attacking the base metal.  TDS
DYNASTRIP Ni-DCSpecially formulated powder that when mixed with water, will provide a safe, electrolytic solution to strip nickel deposits from steel and stainless steel substrates without attacking the base metal. TDS SDS
DYNASTRIP Ni-ENSpecially formulated non-cyanide, alkaline stripper that dissolves high phosphorous, electroless nickel deposits from steel, copper and its alloys by immersion. TDS SDS
DYNASTRIP OMSElectrolytic compound that was specifically formulated to economically strip thermally sprayed tungsten and chrome carbide alloys in a corrosion resistant nickel-copper alloy matrix on mild steel and corrosion resistant substrates. TDS SDS
DYNASTRIP RSSpecially formulated liquid that when mixed with water, will provide an electrolytic rack stripping solution . TDS SDS
DYNASTRIP RTRoom temperature, non-hazardous paint and powder-coating stripper. Can be used on all substrates including zinc and aluminum. TDS SDS
DYNASTRIP RTNRoom temperature, non-hazardous paint and powder-coating stripper. Can be used on all substrates including zinc and aluminum, and is safe to use with silicon masking plugs. TDS SDS
DYNASTRIP SnDynastrip Sn is a specially formulated, peroxide, fluoride and fluoborate free liquid stripper that will strip tin and tin/lead deposits from copper substrates. TDS
DYNASTRIP Sn #2Dynastrip Sn #2 is a specially formulated, peroxide, fluoride and fluoborate free liquid stripper that will strip tin and tin/lead deposits from copper substrates TDS SDS
DYNASTRIP ZnSpecially formulated alkaline, non-cyanide powder that is dissolved with water to strip zinc from steel parts, without attack of the base metal. An alkaline protective film is left on the surface. TDS SDS

Waste Treatment Products

Product NameSummaryCategoryTech Data SheetSafety Data Sheet
DYNATREAT Cr-RReduces hexavalent chrome to its trivalent state in alkaline or acid solutions. Can be added to alkaline cleaners to eliminate the effects of hexavalent chrome contamination. TDS SDS
DYNATREAT Cr-RLA solution of Sodium Bisulfite used for Hex Chrome Reduction.
DYNATREAT DEFOAMER #1Silicated defoamer used to eliminate foam in waste treatment systems and is very effective in either acidic or alkaline aqueous solutions. TDS SDS
DYNATREAT DEFOAMER #2Non-silicated defoamer used to eliminate foam in either acidic or alkaline aqueous solutions. TDS SDS
DYNATREAT DEFOAMER SFEasy to use liquid solution. Silicone-Free defoamer for use in Waste Water treatment applications typically using membrane filtration. TDS SDS
DYNATREAT EFloc-A3Concentrated liquid emulsion, high molecular weight, metal precipitator for flocculation of solids in industrial waste water treatment systems. TDS SDS
DYNATREAT EFloc-C2Concentrated liquid emulsion, high molecular weight cationic metal precipitator for flocculation of solids in industrial waste water treatment systems. TDS SDS
DYNATREAT EFloc-RTUReady to use, liquid emulsion, high molecular weight, anionic metal precipitator for flocculation of solids in industrial waste water treatment systems. TDS SDS
DYNATREAT MC -SPHigh performance liquid poly-aluminum-chloride coagulant that offers superior clarification in potable, wastewater or industrial applications. TDS SDS
DYNATREAT MC-CCLiquid blend of calcium salts to improve coagulation and flocculation in industrial waste water systems. It is particularly effective for aiding in precipitation of phosphates, detergents and oils. TDS SDS
DYNATREAT MP-05Liquid coagulant with a cationic charge, excellent for breaking emulsions formed with oils, inks, surfactants, etc. TDS
DYNATREAT MP-12Polymerized inorganic liquid precipitant formulated for the treatment of waste waters requiring removal of heavy metals - including chelated and complexed ions. TDS
DYNATREAT MP-88Polymerized inorganic liquid precipitant formulated for the treatment of waste waters requiring removal of heavy metals including chelated and complexed ions. Precipitates a wide variety metals simultaneously with minimum sludge generation. TDS SDS
DYNATREAT MP-915Liquid formulated for the reduction of hexavalent chromium and the removal of heavy metals from the effluents of plating baths, etching solutions and rinses in one step. TDS SDS
DYNATREAT MP-970Organic liquid precipitant formulated for the treatment of waste waters requiring removal of heavy metals including chelated and complexed ions. The reaction forms insoluble organo-metallic compounds with minimal sludge generation. TDS SDS
DYNATREAT MP-AMHeavy metal precipitant used to remove metals from waste water streams. It is particularly useful in the treatment of waste water from plating operations. TDS SDS
DYNATREAT MP-FSLiquid polymerized ferric sulphate coagulant based on trivalent iron (Fe3+). Functions very well for both potable and waste water clarification and can be used for turbidity removal, colour removal, phosphate removal and heavy metal removal. TDS
DYNATREAT MP-HSLiquid inorganic heavy-metal precipitant and stabilizer of heavy metals from plating, printed circuit board and other liquid waste streams. Use in conjunction with DYNATREAT coagulants and flocculants. TDS
DYNATREAT MP-SALiquid solution of sodium aluminate that can be used in water treatment as a co-coagulant. Particularly effective in aiding in precipitation by complexing with phosphates, detergents and oils. Very effective in colour and organic removal. TDS
DYNATREAT MP-TRProprietary liquid compound formulated to serve as non-toxic heavy-metal precipitant of heavy metals from industrial process wastewaters, including metals from chelated/complexed environments. TDS SDS
DYNATREAT PFloc-A5Powdered, high molecular weight, anionic metal precipitator for use in wastewater treatment. Neutralizes the negative charge of metal hydroxides, which accelerates the precipitation metals in plant effluent streams. TDS SDS

Toll Blending

Toll Blending Services

Dynamix Inc. offers an extensive range of liquid and powder specialty toll blending products.  

Quality Capabilities

Dynamix is ISO 9001:2008 certified

Production Capabilities

Production capability is in excess of 1 million litres annually

Packaging Options

Liquids

Powder

Equipment